Close

BSA 1” & 30mm (13mm dovetail)

By /

YellowBox13mm Dovetail Range For 13mm Dovetails e.g. most modern BSA air rifles, CZ452 American and early Weihrauch HW35.

PLEASE NOTE SUITABLE DOVETAILS WILL MEASURE APPROXIMATELY 13.5MM AT THE WIDEST POINT.  A B C Dimensions Explained

TO6C

TO6C

2 PIECE MEDIUM DOUBLE SCREW 13mm

A = 19mm / 0.748 inch

B = 21mm / 0.827 inch

D =

Weight 101g

For 1” scopes upto 45mm lens diameter.

View Product
HTO8C13MM

HTO8C13MM

2 PIECE HIGH DOUBLE SCREW 13mm

A = 24mm / 0.944 inch

B = 21mm / 0.827 inch

D =

Weight 111g

For 1″ scopes upto 56mm lens dia.

View Product
TO35C13MM

TO35C13MM

2 PIECE MEDIUM DOUBLE SCREW 13mm

A = 15mm / 0.590 inch

B = 21mm / 0.827 inch

D =

Weight 90g

For 30mm scopes upto 44mm lens diameter on most rifles

View Product
HTO36C13MM

HTO36C13MM

2 PIECE HIGH DOUBLE SCREW 13mm

A = 21mm / 0.827 inch

B = 21mm / 0.827 inch

D =

Weight 111g

For 30mm scopes upto 56mm lens diameter on most rifles

View Product
ATP6113MM

ATP6113MM

2 PIECE HIGH ADJUSTABLE 13mm

A = 22.5 – 23.8mm / 0.885 – 0.937 inch

B = 21mm / 0.827 inch

D =

Weight 119g

Ideal for long range shooting or when scopes turret adjustment is not sufficient when using BSA air rifles etc. Can suit upto 60mm lens diameter on most rifles. Upto 45 MOA vertical adjustment and can be precisely adjusted using the enclosed allen key. Can then be locked using the ‘Double’ Screw clamp. Includes removable arrestor pin. Registered design 4023419

For 30mm scopes upto 60mm lens diameter on most rifles

View Product
HTO7113MM

HTO7113MM

2 PIECE EXTRA HIGH DOUBLE SCREW 13mm

A = 27mm / 1.062 inch

B = 21mm / 0.827 inch

D =

Weight 125g

For 30mm scopes upto 60mm lens diameter.

Ideal for BSA R-10 SE etc with barrel shroud

View Product
Where to buy
Scroll to Top

Height of Scope Mount Required

In each product catergory we state a maximum (upto) objective lens diameter dimension. Due to both rifle and scope designs varying this can only be used as a guide. If you are unsure that the height of the Sportsmatch scope mount you have chosen will be sufficient to clear your rifle scopes objective lens from the barrel of your rifle, we suggest (prior to purchase) you check. The way you calculate the clearance is by halving the overall outside diameter of your rifle scopes objective lens and then deducting half the rifle scopes body tube diameter. For scopes with a 1″ inch diameter body tube diameter this would mean deducting 12.7mm, 15mm for scopes with a 30mm diameter body tube and 17mm for 34mm scopes. This dimension then gives the figure comparible with the ‘A’ dimension that is shown below. The amount our ‘A’ dimension is greater than the figure you have calculated is the amount of clearance your scopes objective lens will be clear of your rifles barrel (dont forget to allow around 2mm for the scope covers). Calculating your rifle scopes clearance in this way does assume your dovetail or Picatinny rail is not raised above or below your rifles barrel. Please consider that rifles with grooved receivers such as some models of airgun and .22 rimfire rifle will mean the scope sits lower than a rifle with a raised dovetail or Picatinny base fitted. Something else to consider is that some rifles with a high or adjustable cheek pieces may require high or extra scope mounts so that your eye is in line with the rifle scope and your head is kept in an upright comfortable position.